Ultima Oil Pump Manual

1. Ultima Oil Pump Manuals
2. Ultima Evo Oil Pump Instructions
3. Ultima Oil Pump Harley
4. Ultima Engine Manual

Removal and Installation

REMOVAL

. VENT Ultima ® Shovelhead engines use a 1992 & later style oil pump as shown in Figure 2. The feed line is mounted in the center of the outer cover of the pump and is pointing up. API service SJ rated motor oils, such as Ultima's 60 weight oil, MW# 103-111. Gear Oil Package (1) Gear Oil Pump (1) Hand Flow Regulator (1) Hand Operated Bucket Pump (1) Hand Operated Drum Pump (16) Hand Operated Pail Pump (4) Lever Action Bucket Pump (1) Manual Cyclic Pumps (1) Oil Can (1) Oil Filter Cart (1) Oil Lube Dispenser (1) Oil Pump (2) Oil Pump Kit (1) Oil Pump Transfer System (13) Oil Pump and Hose Reel Kit. Oil Pump Fits Nissan Altima Sentra 2.5 L QR25DE DOHC 2002-2015. Hitachi OEM Oil Pump VQ35DE 3.5 V6 Engine Fits VQ35DE Pathfinder - QX4 - Murano. Timing Chain Cover Kit Oil Water Pump fit 02-06 Nissan Altima Sentra 2.5L QR25DE.

1. Remove the timing chain. Refer to EM-163, 'Removal'.

2. Remove oil pump assembly.

INSTALLATION

Installation is in the reverse order of removal.

Disassembly and Assembly

1. Oil pump housing

2. Outer rotor

3. Inner rotor

4. Oil pump cover

5. O-ring

6. Regulator valve set

7. Regulator valve

8. Spring

9. Regulator plug

10. Oil strainer

CAUTION: Before assembly apply new engine oil to the parts as shown above.

DISASSEMBLY

1. Remove the oil pump cover.

2. Remove inner rotor and outer rotor from oil pump housing.

3. Remove oil strainer from oil pump housing.

4. After removing regulator plug, remove spring and regulator valve.

INSPECTION AFTER DISASSEMBLY

Clearance of Oil Pump Parts

• Measure clearance with feeler gauge.

• Clearance between outer rotor and oil pump body (position 1).

Standard : 0.114 - 0.260 mm (0.0045 - 0.0102 in)

• Tip clearance between inner rotor and outer rotor (position 2).

Standard : Below 0.180 mm (0.0071 in)

• Measure clearance with feeler gauge and straightedge.

• Side clearance between inner rotor and oil pump body (position 3).

Standard : 0.030 - 0.070 mm (0.0012 - 0.0028 in)

• Side clearance between outer rotor and oil pump body (position 4).

Standard : 0.050 - 0.110 mm (0.0020 - 0.0043 in)

• Calculate the clearance between inner rotor and oil pump body as follows.

1. Measure the outer diameter of protruded portion of inner rotor (position A).

2. Measure the inner diameter of oil pump body with inside micrometer (position B).

(clearance 5) = (inner diameter of oil pump body B) – (outer diameter of inner rotor A)

Standard : 0.045 - 0.091 mm (0.0018 - 0.0036 in)

Ultima Oil Pump Manuals

Regulator Valve

1. Visually inspect components for wear and damage. Mysql.

2. Check oil pressure regulator valve sliding surface and valve spring.

3. Coat regulator valve with engine oil. Check that it falls smoothly into the valve hole by its own weight.

If damaged, replace regulator valve set or oil pump body.

Regulator Valve Clearance Linkin park underground 9 demos download. The night rhonda ferguson was killed pdf reader.

Ultima Evo Oil Pump Instructions

(Clearance 6) = D (Valve hole diameter) – E (Outer diameter of valve)

Standard : 0.040 - 0.097 mm (0.0016 - 0.0038 in)

If it exceeds the standard, replace the oil pump body.

CAUTION: Coat regulator valve with engine oil.

Check that it falls smoothly into the valve hole by its own weight.

Assembly

Assembly is in the reverse order of disassembly.

• Assemble the inner rotor and outer rotor with the punched marks on the oil pump cover side.

CAUTION: Before assembly apply new engine oil to the parts as specified.

Ultima Oil Pump Harley

P1726 electric throttle control system
Description Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM sends the signal to TCM with CAN communication. DTC Logic DTC DETECTION LOGIC DTC CONFIRMAT ..

P2118 throttle control motor
Description The throttle control motor is operated by the ECM and it opens and closes the throttle valve. The current opening angle of the throttle valve is detected by the throttle position sensor and it provides feedback to the ECM to control the throttle control motor to make the thrott ..

Corrosion protection
Description To provide improved corrosion prevention, the following anti-corrosive measures have been implemented in NISSAN production plants. When repairing or replacing body panels, it is necessary to use the same anti-corrosive measures. Anti-Corrosive Precoated Steel (Galvannealed Steel) ..

Th3InfamousI

Ultima Engine Manual